Torque limit Cancel Okuma Control
G28 Torque limit: Cancel This cancels the torque limit instruction made by G29. [Command format] G28[Applicable specification]...
View ArticleTorque limit G29 Okuma Control
G29 Torque limit This restricts the maximum output torque of the feed axis servo motor. [Command format] G29 PX=___ PZ=___ PW=___[Note] 1....
View ArticleSkip cycle G30 Okuma Control
G30 Skip cycle This is used in the measurement subprogram such as the touch sensor and touch setter.[Command format] G30 X___ D___ L___ Z___ C___ (Compound...
View ArticleFixed thread cutting cycle Longitudinal Okuma Control
G31 Fixed thread cutting cycle: Longitudinal [Command format] G31 X___ Z___ I__ (E__) F__ (K__) (L__) (J__) (C__) A__ X: Thread diameter at each thread...
View ArticleFixed thread cutting cycle End face G32
G32 Fixed thread cutting cycle: End face [Command format] G32 X__ Z__ K__ (E__) (I__) (L__) F__ (C__) X: Coordinates of ending point of end face thread cutting Z:...
View ArticleFixed thread cutting cycle Longitudinal G33
G33 Fixed thread cutting cycle: Longitudinal [Command format] G33 X__ Z__ I__ (E__) (F__ (K__) (L__) (J__) (C__) A__ X: Thread diameter at each thread...
View ArticleVariable lead thread cutting cycle Increasing lead Okuma Control
G34 Variable lead thread cutting cycle: Increasing lead [Command format] G34 X__ Z__ (E__) F__ (C__) (J__) X: Thread cutting target point Z: Thread cutting target...
View ArticleVariable lead thread cutting cycle Okuma Control
G34 Variable lead thread cutting cycle: Increasing lead [Command format] G34 X__ Z__ (E__) F__ (C__) (J__) X: Thread cutting target point Z: Thread cutting target...
View ArticleVariable lead thread cutting cycle Decreasing lead
G35 Variable lead thread cutting cycle: Decreasing lead [Command format] G35 X__ Z__ (E__) F__ (C__) (J__) X: Thread cutting target point Z: Thread cutting target...
View ArticleFeed-shaft synchronized feed for M-tool spindle
G36 Feed-shaft synchronized feed for M-tool spindle: Forward [Applicable specification] Compound machine
View ArticleFeed-shaft synchronized feed for M-tool spindle
G37 Feed-shaft synchronized feed for M-tool spindle: Reverse [Applicable specification] Compound machine
View ArticleTool nose radius compensation Cancel
G40 Tool nose radius compensation: Cancel This cancels tool nose radius compensation instructed by G41 or G42.
View ArticleFanuc Panel Keys
Address keys The area of the MDI keypad that allows an operator to enter letters and special characters into the control. ALARM keys Keys located on the machine panel that display alarm information for...
View ArticleTool nose radius compensation Left
G41 Tool nose radius compensation: Left For lathe machining, this functions as the tool nose radius compensation-left. This is instructed when the center of tool (center of nose radius)...
View ArticleCutter radius compensation Right
G42 Cutter radius compensation: Right For lathe machining, this functions as the tool nose radius compensation-right. This is instructed when the center of tool (center of nose radius) passes...
View ArticleZero offset, maximum spindle speed designation
G50 Zero offset, maximum spindle speed designation When this is instructed to the same block as the S command this function as the spindle speed maximum command. In other cases, it functions...
View ArticleMirror image coordinate selection check Okuma Control
G62 Z-axis mirror image coordinate selection check Whether the Z-axis program coordinate system is used as the fundamental or mirror image coordinate system is instructed at the head of...
View ArticleDroop control OFF Okuma Control
G64 Droop control OFF The feed axis is controlled to follow the computed value. For this reason, the actual axis position is behind the computed value. The droop control prohibits to issue...
View ArticleDroop control ON Okuma Control
G65 Droop control ON The feed axis is controlled to follow the computed value. For this reason, the actual axis position is behind the computed value. The droop control prohibits to issue...
View ArticleCompound fixed thread cutting cycle Longitudinal Okuma Control
G71 Compound fixed thread cutting cycle: Longitudinal [Command format] G71 X_ Z_ A_ B_ D_ U_ H_ L_ E_ F_ J_ M_ Q_ I X: Final cutting depth of thread cutting...
View ArticleEnd face thread cutting compound fixed cycle Okuma Control
G72 End face thread cutting compound fixed cycle [Command format] G72 X_ Z_ A_ B_ D_ W_ H_ L_ E_ F_ J_ M_ Q_ K X: Coordinates of ending point for thread...
View ArticleLongitudinal grooving compound fixed cycle
G73 Longitudinal grooving compound fixed cycle [Command format] G73 X_ Z_ I_ K_ D_ L_ F_ E_ T_ X: X coordinates of target point Z: Z coordinates of target point...
View ArticleEnd face grooving compound fixed cycle Okuma Control
G74 End face grooving compound fixed cycle[Command format] G74 X_ Z_ I_ I_ K_ D_ L_ F_ E_ T_ X: X coordinates of target point Z: Z coordinates of target point I:...
View ArticleG75 Automatic chamfering Okuma Control
G75 Automatic chamfering Corners of work can be chamfered using a simple program. [Command format] G75 G01 X_ L_ F_ Z_ X and Z: Instruct target...
View ArticleAutomatic rounding Okuma Control G76
G76 Automatic rounding Corners of work can be rounded using a simple program. [Command format] G76 G01 X_ L_ F_ Z_ X and Z: Instruct target points...
View Article
More Pages to Explore .....